Readers searching for an stl viewer who also need durable printed tags will find guidance on ring hole dimensions and related keychain settings here. The article explains how thickness, borders, walls, and filament choice affect the part that usually fails first.
The ring is usually the first part of a printed keychain to flex, crack, or tear, so its dimensions deserve more attention than the lettering. This guide explains how base thickness, raised height, hole diameter, border width, total size, walls, and filament work together for a tougher tag.

The short version
- Start with a 3 mm base, 1.2 mm raised detail, and a 4 mm ring hole. That produces a 4.2 mm total thickness with a useful balance of strength and weight.
- Keep the ring area substantial: the default hole has a 2.4 mm wall around it, while a base under 2 mm can flex and crack.
- Use a 2.5 mm border as a starting point, and avoid going below 2 mm around thin script letters.
- Print flat with 3 or more walls. PLA suits gifts, while PETG is tougher for a keychain carried in a pocket or left in a car.
Why the ring hole fails first
A keychain gets pulled from the ring, twisted against keys, and dropped onto hard surfaces. The ring hole concentrates that force in a small area at the edge of the plate. If the base is too thin, the material around the hole bends instead of distributing the load across the tag.
The custom keychain maker makes the ring part of the design rather than leaving you to cut a hole into a finished model. It places the hole on the left edge at mid-height, adds the surrounding plate, and lets you set the total width, base thickness, raised height, hole size, and border.
The important point is that these settings are connected. A larger hole removes more material. A thinner base gives the remaining ring wall less support. A narrow border leaves less material between the lettering and the edge. Fixing only one setting may not solve a weak ring if the other dimensions are working against it.

The Keychain Maker page brings the strength-related dimensions into one settings panel.
Start with a strong baseline
For a general name tag or logo keychain, these are sensible starting values:
- Total width — 50 mm, including the ring
- Base thickness — 3 mm
- Raised height — 1.2 mm
- Ring hole — 4 mm
- Border — 2.5 mm
- Walls — 3 or more in the slicer
- Layer height — 0.2 mm for ordinary lettering
The 3 mm base and 1.2 mm raised detail give a 4.2 mm total height. The raised section is high enough to see and feel, while the base gives the ring a solid body. The 4 mm hole is the default because it fits most metal split rings and ball chains, and the surrounding ring wall is 2.4 mm wide.
For a tag that will be handled roughly, increase the base to 4 mm rather than making the raised letters much taller. Extra height changes the appearance and print time without adding as much support to the hole area as a thicker base.
Tune the five dimensions in order
When a keychain is weak or awkward, change one design setting at a time. This makes the cause easier to identify.
- Check total width first. The width includes the ring, so making the whole keychain smaller also shrinks the lettering and the space available around it. A width of 40–60 mm suits a house key ring. At 40 mm, fine logo details under 1 mm may not show clearly.
- Set the base thickness. Keep 3 mm for normal use. Use 4 mm when the tag will be pulled hard or carried with heavy keys. Avoid going below 2 mm because the ring area can flex and crack.
- Set the hole diameter. Keep 4 mm for most split rings. Use 5 or 6 mm for a thick ring or lanyard, and about 3 mm only for a thin chain. A larger hole is not automatically stronger: it removes more material from the ring.
- Protect the edge with the border. A 2.5 mm border is a useful starting point. Thin script needs room around its curves, so avoid setting the border under 2 mm when the letters have narrow strokes.
- Adjust the raised height last. Use 1.2 mm for readable, tactile lettering. The maker describes that as six layers at 0.2 mm. For small script names, use 0.12 mm layers rather than immediately making the lettering taller.
The plate shape matters too. Follow letters hugs a name outline, while Rounded tag creates a classic rectangular plate and is often more forgiving for a small logo. If the ring seems to stick out too far beside a curved first letter, Rounded tag gives it a straighter edge to meet.
Match the design to the filament
The model settings cannot compensate for every printing choice. Print the keychain flat, base down, as exported, with no supports. That keeps the broad base attached to the build surface and avoids adding a weak supported underside.
Use at least 3 walls so the ring does not tear out easily. Infill still matters, but the outer walls are especially important around a hole because they form much of the ring's perimeter. A sparse interior does not make a thin base stronger by itself.
PLA is the straightforward choice for gifts and colorful batches. It is easy to print and available in many colors, but it softens at around 60 °C, so a tag left on a hot dashboard can warp. PETG is tougher and better suited to a keychain that spends its time in a pocket or car.
For two colors, the downloaded 3MF keeps the base and raised letters as separate parts for an AMS or another multi-material system. With a single nozzle, use the STL and add a filament change at the base thickness, which is 3 mm by default. The raised lettering then prints in the second color.
Diagnose common ring problems
The ring cracks near the plate. Increase the base from 3 mm to 4 mm, keep at least 3 walls, and inspect the border around the first letter. A script curve that pinches the edge can leave too little material even when the nominal border looks adequate.
The metal ring does not fit. Check the hole before changing the entire keychain. The default 4 mm works for most split rings and ball chains. Move to 5 or 6 mm for thicker hardware. Do not reduce the hole below the wire diameter just to preserve more plastic.
The tag bends when handled. The base may be under 2 mm, or the ring may be oversized relative to the plate. Restore the 3 mm baseline, or use 4 mm for rough handling. PETG can also be a better filament choice than PLA for a working keychain.
The letters break away. Check the border, especially around thin script. Keep it at 2.5 mm or avoid going below 2 mm. If the tag is small, use 0.12 mm layers so the lettering resolves more cleanly instead of increasing the raised height.
The ring lands farther out than expected. The hole is fixed to the left edge at mid-height. An inward-curving first letter can make the ring appear more separated from the design. Switch to Rounded tag or adjust the border so the ring meets a straighter edge.
Check the exported file before printing
A watertight badge under the preview means the generated file is a closed solid, but it is still worth checking the file you plan to slice. The STL is one solid body. The two-color 3MF contains separate base and letter parts, so confirm that both objects are present before assigning filaments.
A 3mf viewer is useful for this inspection. It shows every object, standard 3MF colors, the bounding-box size, triangle count, and mesh count in the browser. Orbit the model, enable wireframe, and verify that the ring is attached to the plate and that the raised lettering has not disappeared.

The 3MF Viewer makes it possible to inspect the separate base and raised-letter objects before opening a slicer.
If the file is an STL from another source, remember that STL has no units. A model intended as 4 inches can open as 4 mm if the source unit is misunderstood. The stl to 3mf converter lets you identify the STL as millimeters or inches, then writes a 3MF with millimeter units, welded vertices, centered placement, and the model resting on z = 0.

The STL to 3MF page exposes the unit choice and output dimensions before conversion.
This conversion does not add color. STL has no color data, so the resulting 3MF remains a single-color object. Paint or assign filaments in the slicer afterward, or use the separate two-color export from the keychain maker when the design begins there.
FAQ
Is 3 mm thick enough for a printed keychain?
It is a good starting base thickness for normal use. Keep the raised detail at 1.2 mm and use at least 3 walls. For rough handling, increase the base to 4 mm. Avoid going below 2 mm because the ring area can flex and crack.
Should I make the ring hole bigger or smaller?
Use the default 4 mm for most metal split rings and ball chains. Choose 5 or 6 mm for thick rings or lanyards. Go down to about 3 mm only for a thin chain, and make sure the ring wall still has enough material around the hole.
Why did the ring break even though the letters look fine?
The lettering can print perfectly while the ring remains weak. Check the base thickness, number of walls, hole size, and border. A 3 mm base, 4 mm hole, 2.5 mm border, and 3 or more walls provide a stronger starting combination than a thin base with a large hole.