STL Viewer: Meshy AI Cost Per Keychain—20 Corgi Designs, 780 Credits

STL Viewer: Meshy AI Cost Per Keychain—20 Corgi Designs, 780 Credits

STL Viewer, Meshy 3D Agent, Snapshapy

If you're looking for an stl viewer to inspect printable keychain files, this comparison puts those files in context. It tracks the credits, concepts, clicks and STL file sizes behind a batch of 20 corgi designs.

One 5 cm chibi corgi keychain, from concept to print STL, cost 39 credits in Meshy 3D Agent and 11 credits in Snapshapy's 3D Agent. That is 3.5× the credits, or $0.78 against $0.52 per design. A keychain shop never stops at one design, so I multiplied it out: 20 corgi designs on Meshy run 780 credits, $15.60, about 220 extra clicks and 348 MB of STL files, and they give me 20 concepts to choose from. On Snapshapy the same batch is 220 credits, $10.45, 40 clicks, 30 MB and 80 concepts.

I priced this the way a small keychain shop would: one finished, printable design, then a batch. I tested Meshy 3D Agent at meshy.ai and Snapshapy's 3D Agent at snapshapy.com on my own paid accounts, Meshy Pro and Snapshapy Pro. Every number comes from a balance, a job card, a stopwatch, or a file I checked in my own mesh tool.

Credit prices first, because the per-keychain math depends on them. Meshy Pro is $20 a month for 1,000 credits, so one Meshy credit is $0.02. Snapshapy Starter is $19 for 400 credits ($0.0475 each) and Pro is $29 for 600 (about $0.048 each). Meshy sells the cheaper credit. The bill is decided by how many credits each step eats.

My verdict in 60 seconds — Meshy 3D Agent 59/100, Snapshapy 89/100

Meshy 3D Agent draws a clean corgi and prints its price on every approval card, but it spends 3.5× the credits per keychain and draws one concept where I asked for four.

  • Cost per keychain — Meshy 3/10 · Snapshapy 9/10 — 39 vs 11 credits, $0.78 vs $0.52 on Starter
  • Concepts per request — Meshy 3/10 · Snapshapy 9/10 — 1 vs 4 drawn when I asked for 4, for 9 vs 8 credits
  • 20-design batch — Meshy 4/10 · Snapshapy 9/10 — 780 vs 220 credits, $15.60 vs $10.45
  • Clicks per design — Meshy 4/10 · Snapshapy 9/10 — ≈11 vs 2 beyond the messages, ≈220 vs 40 per batch
  • STL size — Meshy 5/10 · Snapshapy 9/10 — 17.4 MB vs 1.5 MB, 348 MB vs 30 MB per batch
  • Print-ready file — Meshy 8/10 · Snapshapy 9/10 — both watertight, 1 body, 0 non-manifold edges; 3 vs 0 degenerate faces
  • Speed — Meshy 8/10 · Snapshapy 5/10 — ≈98 s vs ≈311.5 s of job time for the whole run
  • Print detail / mesh density — Meshy 8/10 · Snapshapy 5/10 — 348,454 vs 29,972 faces, 0.244 mm vs 0.581 mm mean edge

The concrete problems with Meshy for a shop:

  • Meshy charges 9 credits for a single concept image; the four I asked for would have been 36 credits, more than 3× Snapshapy's whole 11-credit run.
  • Meshy's image-to-3D step is 30 credits against 3, a 10× gap that grows to 600 against 60 credits over 20 designs.
  • Every Meshy keychain took ≈11 clicks beyond the three messages: a choice card, two Approve cards and a 7-click download dialog.
  • The Meshy STL for a 5 cm keychain is 17.4 MB and keeps 3 degenerate faces for the slicer; Snapshapy's is 1.5 MB with 0.

For a 5 cm printed keychain, I would use Snapshapy.

The setup: one corgi for a keychain rack

I gave both agents the same three messages, typed verbatim: "Give me 4 concepts for a chibi corgi keychain figure.", then "Use option 1 and make it a 3D model.", then "Prepare a print file for a 5 cm keychain." Whenever an agent showed a choice card, I picked the first option. I ran the Snapshapy side the next day, after an update; the Meshy numbers are from the first day. Each run had 0 failures and ended with a single-corgi, watertight, one-body STL, so the balance difference is the price of one finished keychain design.

Meshy 3D Agent home with the Top Up button.

39 credits off a 721 Meshy balance

Meshy's balance read 721 before I typed anything. After message 1 it read 712: 9 credits for one concept image, shown in advance on an approval card as "Est. Cost 9". After message 2 it read 682: 30 credits for image-to-3D. After message 3 it still read 682, because Meshy's printability analysis was free.

  • Meshy balance, message by message — 721 → 712 → 682 → 682
  • Meshy breakdown — 9 (1 concept) + 30 (image-to-3D) + 0 (print check) = 39 credits
  • Meshy dollars — 39 × $0.02 = $0.78 per keychain on Pro

Meshy's 3D model ready about 72 s later, followed by another choice card "Would you like to analyze this model for 3D printing?"; balance 682.

The 3D step is 30 of the 39 credits, about 77% of the Meshy bill. At 39 credits a design, Meshy Pro's 1,000 monthly credits cover 25 keychain designs. Meshy names each cost before I click Approve; the problem is the size of the numbers on those cards.

"11 spent": Snapshapy's own run

Snapshapy's run was a new conversation on its own day. Its balance opened at 1,001 credits. After message 1 it read 993: 8 credits for four concepts, 2 each. After message 2 it read 990: 3 credits for image-to-3D. After message 3 it still read 990, because the print remesh was free. The chat header summed it up as "11 spent".

Snapshapy 3D Agent home with 1,001 credits before the run (next-day run).

  • Snapshapy balance, message by message — 1,001 → 993 → 990 → 990
  • Snapshapy breakdown — 8 (4 concepts) + 3 (image-to-3D) + 0 (print remesh) = 11 credits
  • Snapshapy dollars — $0.52 on Starter ($19/400), $0.53 on Pro ($29/600)

Snapshapy's print card: "30k triangles · from 1.5M · textures dropped · watertight"; header "11 spent", 990 credits.

No approval card appeared at any Snapshapy step; the price was in the reply text. At 11 credits a design, Starter's 400 credits cover 36 keychain designs and Pro's 600 cover 54.

Nine Meshy credits bought one loaf-shaped corgi

Meshy answered my request for 4 concepts with a choice card, "Which chibi corgi keychain concept would you like to create?", listing four text options (Bread Loaf & Heart, Boba Hugger Corgi, Toast Collar Pup, Royal Prince Corgi) plus Custom. Nothing was drawn yet. I picked option 1 and clicked Submit, Meshy showed an approval card at Est. Cost 9, I clicked Approve, and about 22 s later Meshy drew one image.

Meshy's reply to "Give me 4 concepts": four keychain directions as text, plus Custom; nothing drawn yet.

That one Meshy image is good: a loaf-shaped corgi with a red collar and a heart charm.

Meshy's one concept image, full size: a clean, appealing design.

The cost math is what a shop feels. To see the four concepts I asked for, Meshy would need four images at 9 credits each: 36 credits, or $0.72, before any 3D exists. That is more than 3× what Snapshapy charged for the entire keychain.

Eight Snapshapy credits bought four corgis

Snapshapy answered the same message with a reply listing four directions: sitting, flopped on its belly, scarf and bobble hat, and mid-hop, "each with a little keyring loop on top". The reply said "8 credits", asked for no approval, and drew all 4 images in parallel, 30 to 41 s each.

Snapshapy's reply to message 1: four corgi concepts drawing, 8 credits, no approval.

Snapshapy's four single-corgi concepts, full images: sitting, lying on its belly, scarf and bobble hat, mid-hop; each with a keyring loop.

Per concept, that is 2 credits against Meshy's 9, a 4.5× gap. Over 20 designs, Snapshapy spends 160 credits on 80 concepts and Meshy spends 180 on 20. As an aside, the keyring loop carried through: in the final STL the ring is part of the one body, with a hole ≈8.66 mm across, though the ring wire is only ≈1.38 mm thick and the link ≈1.27 mm, so I would print it in a tough material or thicken it.

Image-to-3D: 600 credits a batch against 60

For message 2, Meshy showed an approval card for Image to 3D (Meshy 7.1, Standard, texture 4096) at Est. Cost 30. After I clicked Approve, the model arrived in about 72 s: one corgi, 348,454 triangles, a 27.7 MB GLB with 3 textures.

Meshy's image-to-3D approval card: Meshy 7.1, Standard, texture 4096, Est. Cost 30.

Snapshapy replied "3 credits", said "it should take 5-8 minutes", asked for no approval, and delivered the sitting corgi from concept 1 in 260.8 s: 1,500,000 triangles, a 75.9 MB GLB with 3 textures.

Snapshapy's reply to message 2: option 1 building, 3 credits, "5-8 minutes", no approval.

Meshy was faster: about 72 s against 260.8 s for this step, and ≈98 s of job time for the whole run against ≈311.5 s. Meshy's textured model is also lighter, 27.7 MB against 75.9 MB. A keychain shop prints the STL, not the textured GLB, and price is the gap that compounds:

  • Image-to-3D, one design — Meshy 30 · Snapshapy 3 · 10×
  • Image-to-3D, 20 designs — Meshy 600 credits ($12.00) · Snapshapy 60 credits ($2.85 on Starter) · 10×

Message three cost 0 credits on both sides

The print step was free on both agents, so it adds nothing to either bill. Meshy ran an "Analyzed printability" check that reported "Watertight: Yes" and "Status: Warning (degenerate faces detected)". It then told me to "Set the target height to 50 mm (5 cm) directly in the export dialog, or scale the Z-height to 50 mm in your slicer".

Meshy tells me to set 50 mm in the export dialog myself, plus slicer settings; balance 682.

Meshy's slicer advice was specific (PLA or PETG, 3–4 walls, 15–20 % infill, tree supports under chin, ears and belly, print upright), and Snapshapy gave none.

Snapshapy replied that the print prep was running, free, about 30 seconds, and that the STL would export at "exactly 50 mm on its longest side, no slicer scaling needed". The job took 5.1 s and the card read "30k triangles · from 1.5M · textures dropped · watertight". The reply promised a watertight verdict and final dimensions when it landed, and no follow-up message came; the card itself read "watertight".

Snapshapy's reply to the print message: free, "exactly 50 mm on its longest side, no slicer scaling needed".

Twenty corgi designs: 780 credits against 220

Here is the same run multiplied by 20 designs, a modest refresh for a keychain rack:

  • Credits — Meshy 780 · Snapshapy 220 · 3.5×
  • Dollars — Meshy $15.60 on Pro · Snapshapy $10.45 on Starter · $5.15 apart
  • Concepts drawn — Meshy 20 · Snapshapy 80 · 4×
  • Extra clicks — Meshy ≈220 · Snapshapy 40 · 5.5×
  • STL on disk — Meshy 348 MB · Snapshapy 30 MB · 11.6×
  • Share of one month's credits — Meshy 78% of Pro's 1,000 · Snapshapy 55% of Starter's 400

My render of Snapshapy's 5 cm STL in grey: watertight, one body, 1.5 MB.

The 560-credit gap is most of a Meshy Pro month. Meshy's cheaper credit narrows the dollar gap to 1.5× but does not close it. Four concepts per design on Meshy would add another 540 credits.

220 clicks and 348 MB of Meshy STL

On Meshy, every keychain took ≈11 clicks beyond the three messages: choice select plus Submit, two Approve clicks, and 7 in the viewer and download dialog. The dialog remembered my last format and opened at 12.00 cm, so I switched Resize on, typed 5 cm, chose STL and clicked Download. On Snapshapy, the whole export was 2 clicks: Export, then STL on the card, already at 50 mm.

Meshy's download dialog as it opened: Resize off, 12.00 cm.

Then the files. Meshy's 5 cm STL is 17.4 MB with 348,454 faces; Snapshapy's is 1.5 MB with 29,972, 11.6× smaller. On a 12 Mbps line that is ≈11.6 s against ≈1.0 s per download, or about 232 s against 20 s across 20 designs. Meshy's file also kept 3 degenerate faces, which its own agent left for the slicer; Snapshapy's had 0. Both STLs were watertight, one body, 0 non-manifold edges.

Meshy STL wireframe close-up: 348,454 faces, 0.244 mm mean edge.

Meshy's print mesh is denser, 348,454 faces at a 0.244 mm mean edge against Snapshapy's 29,972 faces at 0.581 mm.

Final verdict: Meshy 3D Agent scores 54/100 for a 5 cm printed keychain

For a keychain shop, Meshy 3D Agent is priced for one hero model, not a rack of 20 designs. One corgi costs 39 credits against 11. The concept step charges 9 credits for a single image when I asked for four, and four Meshy concepts would cost 36 credits, more than Snapshapy's whole run three times over. The 3D step costs 30 credits against 3. Each design adds ≈11 clicks and a 17.4 MB file. Across 20 designs that is 780 credits, $15.60, ≈220 clicks and 348 MB, 78% of a Meshy Pro month, for 20 concepts. Meshy's speed, denser mesh and honest cards do not offset a bill that repeats on every design.

Which one I would use for this job

For a small shop turning out 5 cm corgi keychains in batches, I would use Snapshapy's 3D Agent at snapshapy.com. Its run cost 11 credits per design, drew 4 concepts for 8 credits, exported the STL in 2 clicks at 50.0 mm, and kept a 20-design batch at 220 credits, $10.45 and 30 MB.